Видео

Amazing video. Nearly purchased a new one. Mine was doing exactly the same but when i dismantled and tested it first to make, sure mine was spraying like a firemans hose from that aforementioned fitting as i switched on without even activating the lance. No wonder i had hardly any pressure when i tried using it last weekend. Part ordered now. Well done and thanks

If you clean it how long does it take till u clean again? As u guessed I'm a woman, but I'm willing to give it ago, without having to replace it hopefully

Best video on stitching, starting and cancelling threads 👌🏽

but also 4 ft of 6mm hose, a container, plyers, gloves, allan key/screwdriver/ bolt, laptop or computer to look up relay and where its located, yep only paper clip, or just use the key, unless your stealing the gas.

Nice one, good info ,one love 👍

Good

Good grief. 😮. I’d buy a new one. I bet that vehicle was puffing black smoke ? Which begs a question, everything else is caked up ?

He took half the car apart 😂

Did u fit a boost gauge and do you know where u fed the vac lin into the car ?

I have the same EGR valve type, and it's time for cleaning it. How did you manage to remove it from the engine?

"Probably the best video ever"? lol

Excellent. Good soothing music

to wash the engine bay, use cold Coca-Cola, and spray it on the motor, on a heated motor, but not too hot. this will produce a thermal, chemical cleaning reaction. instead of Coca-Cola you can also use Fanta. please make a video about it.

Hi, great video, thanks a lot for that! I am thinking about ordering two locks (right/left; one for each side side) for my wife's Meriva B from 2011. Is there any problem with shipping to Germany? Any tax or customer problems after Brexit? Thanks a lot. Marc

😱😯🤮

The scrapyard use an ice axe to puncture the fuel tank and a flat tray to collect the fuel.

Top man - simple, concise, helpful advice . Thank you

Great video thanks. I clean mine about every six months as the valve stuck open once and the car died as it was essentially running on exhaust gas. What I do is unbolt the motor from the back and push the sprung valve in and out to clean the shaft too. What happens is the carbon sticks to the valve stem and stops the spring from closing the valve again. Be careful though and make sure you only press the middle of the valve stem. If you press on the retaining plate the split collects can come off. It's then a fiddly two person job to fit them back on and trapping them back under the plate. Dismantling it like this is the best way to clean it but isn't for the feint hearted. If you lose one of those collets you could be looking at a new valve ££££.

If oven cleaner works, and bicarb/vinegar is better than oven cleaner for cleaning ovens, then logic would dictate that it would be just as effective for EGRs :)

My katcher k2 is releasing water in the correct way but very weak. Would you know what the problem is please

damn man, that looks like a new one! well done

Where did you get the part from? As I believe I have the same issue with our K2.

yeah but but did that fix the EGR fault?

Well done, where can I find 2016 sonata EGR on my engine

Benefting from this video to this day! Spent a long time trying to read instructions and understand other videos watched this carefully got it straight away

Old fashioned siphoning is much simpler and will work on cars with dead or missing battery.

Hello. Thanks for the video. It was very helpful. Next month I’m going to my storage where I have my car in and I’ll need to drain old gas that has been in the tank for 8 years. It’s a Pontiac sun fire 03 and the fuel filter is at the bottom of the car near the fuel tank. Any advice would be appreciated as I’ve never done this before. I have changed the fuel filter before so I know how to remove the fuel relay before removing the fuel filter so that gas doesn’t come spitting out from the bottom. So I don’t make a mess, would it work if I just connected connected a hose on the fuel line after removing the fuel filter and then plug the fuel relay back in and have it drain all out that way? I don’t have a lift so I’ll be doing everything from the ground. How high will I need the rear of the car jacked up if at all to remove all fuel? I look forward to your reply. I think I can do this by myself but I’d like some step by step guidance if you wouldn’t mind. It’s a nice car with only 55k kilometers on it and I plan on using the car. Any other advice on what I should do with the car before turning it on. It has been on stands inside the storage unit since January of 2017. The oil was changed a little before storing it.

yeahman

Holy crap, I never even thought of this. So glad I found this before I went drilling holes in things. All the thanks!

Good way to roast the fuel pump.

Good vid this! Exactly what I needed to hear! Thank you my man! 🙏🏼

Drive ix35 diesel common problem

I use brake and carb cleaner it works best to cleaning it

A good video fix, the elbow joint breaks because of stress put onto it from the stupid hose that is getting wrapped up like a snake and making people mad pulling it apart

I've used this method before, as well.

top man if it save money i,m all for it ,, been fleeced enough by garages

I have the same problem after changing the front left and right hub, the front left is coming up as a mechanical error. I need to tackle it, but I don't know what could cause it on a new bearing and hub.

Hi BMAC, great video btw! How did you get to the plot you are showing with the spikes from VCDS? Thanks

How to change the egr ?

Thank you so much 🫶🏼 you’ve just saved me a fortune 🙌🏼

Best I have seen, Thank you.

Can someone please help me with info on installing this on my Audi A1 2013 please. Thank you.

Good video with great detail, thanks

the air pipes of my airtrek are wider in diameter. What to do?

Does it damage the engine after a while?

Great vid . Z Cool, but my pump is mechanical . So working it out .

brooo you installed it totaly wrong. the bottom part of bov must face to boost side......

Why do you use a paper clip at all, cant you do that with the relay on? 🤔

Very good vid

This is the best and ONLY tutorial that was simple and clear enough for me to follow along and install my own steering wheel cover within 1 hour first try! I've then gone on to install many others simpl8bssed off this video- well done and thanks for the grest content 🫡💯 So good I forgot I left a comment already 1 year ago haha